Nexus N9K loader > prompt and boot release software from loader

07.08 2020 | by massimiliano

Se vi trovate nella situazione in cui all’accensione di uno switch Nexus N9K (nel mio caso è un C93180YC-FX) non […]

Se vi trovate nella situazione in cui all’accensione di uno switch Nexus N9K (nel mio caso è un C93180YC-FX) non dovesse partire (status led arancione lampeggiante eppoi tutto spento…) e quando ci colleghiamo in consolle lo switch si presenta cosi:

loader >

per farlo partire basta digitare i seguenti comandi:

loader > dir

bootflash::

lost+found

aci-n9000-dk9.14.2.4i.bin

auto-s

CpuUsage.Log

lxc

libmon.logs

disk_log.txt

mts_buffer_log.log

mem_log.txt

diag_bootup

loader >

loader > boot aci-n9000-dk9.14.2.4i.bin

Security Lock

Booting aci-n9000-dk9.14.2.4i.bin

Trying diskboot

Filesystem type is ext2fs, partition type 0x83

Image valid

Image Signature verification was Successful.

Boot Time: 8/5/2020 12:35:21

Security Lock

[ 0.000000] Reserving ebda at 0x9f000 Len 0x61000

[ 5.180351] swapper/0 (1) Ran 4641 msecs in last 5000 msecs

q▒v▒▒vr▒▒▒▒p▒{▒▒▒switching root to tmpfs

switch_root: faiUsage: grep [OPTION]… PATTERN [FILE]…

Try `grep –help’ for more information.

Found card_index=21134

*** Running INXO[ 10.606684] @@@@@@FPGA reg val is: 1564687 @@@@@@@@@

S PE IFC image ***

*** Running INXOS PE IFC image ***

Skip /var/sysmgr setup to S26 script HW: 1, IFC: 1

*** Running INXOS PE IFC image ***

Starting udev

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-cfg0: recovering journal

Setting free inodes count to 78199 (was 78229)

Setting free blocks count to 298971 (was 299000)

/dev/hd-cfg0: clean, 41/78240 files, 13605/312576 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-cfg1: recovering journal

Setting free inodes count to 78201 (was 78229)

Setting free blocks count to 298973 (was 299000)

/dev/hd-cfg1: clean, 39/78240 files, 13603/312576 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-pss: recovering journal

Setting free inodes count to 78184 (was 78229)

Setting free blocks count to 298875 (was 299000)

/dev/hd-pss: clean, 56/78240 files, 13701/312576 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-bootflash: recovering journal

Setting free inodes count to 774412 (was 781813)

Setting free blocks count to 2121857 (was 3036280)

/dev/hd-bootflash: clean, 7412/781824 files, 1003903/3125760 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-logflash: recovering journal

Setting free inodes count to 2580224 (was 2580469)

Setting free blocks count to 9831659 (was 10108024)

/dev/hd-logflash: clean, 256/2580480 files, 483349/10315008 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-recovery: recovering journal

/dev/hd-recovery: clean, 11/625856 files, 77552/2500608 blocks

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-ifc-log: recovering journal

Setting free inodes count to 781760 (was 781813)

Setting free blocks count to 3030809 (was 3036024)

/dev/hd-ifc-log: clean, 64/781824 files, 94695/3125504 blocks

Early mount of filesystems

@@@ Check if sda9 is encrypted

@@@ sda9 is encrypted

@@@ Mounting /dev/sda9 with crypto support

@@@ PRE initialize crypto partition

@@@ Found crypto key. Just open the mapper device

@@@ Open mapper device successfully!!!!

@@@ Mounting map-sda9 to /mnt/ifc/cfg

*** Running INXOS PE IFC image ***

Starting Bootlog daemon: bootlogd.

Total disk size (MB)128030

dumpe2fs 1.42.1 (17-Feb-2012)

Starting mcelog daemon

dumpe2fs 1.42.1 (17-Feb-2012)

fs_cmd for sda9 is dumpe2fs -h /dev/map-sda9

dumpe2fs 1.42.1 (17-Feb-2012)

mount: /dev/sda5 already mounted or /mnt/cfg/0 busy

mount: according to mtab, /dev/sda5 is already mounted on /mnt/cfg/0

*** Running INXOS PE IFC image ***

fs_cmd for sda9 is dumpe2fs -h /dev/map-sda9

Total free space (MB)19206

Total partitions found 9

Start early extraction of system image

mount: /dev/sda4 already mounted or /bootflash busy

mount: according to mtab, /dev/sda4 is already mounted on /bootflash

*** Running INXOS PE IFC image ***

Enter system maintenance mode? (y/n) [n]: ### For now falling back to system mode always ###

Checking partition structure

Total disk size (MB)128030

dumpe2fs 1.42.1 (17-Feb-2012)

fs_cmd for sda9 is dumpe2fs -h /dev/map-sda9

dumpe2fs 1.42.1 (17-Feb-2012)

fs_cmd for sda9 is dumpe2fs -h /dev/map-sda9

Total free space (MB)19206

Total partitions found 9

Checking all filesystems………4

[S26check-flash] logflash cleanup finised.

done.

mount: /dev/sda5 already mounted or /mnt/cfg/0 busy

mount: according to mtab, /dev/sda5 is already mounted on /mnt/cfg/0

mount: /dev/sda6 already mounted or /mnt/cfg/1 busy

mount: according to mtab, /dev/sda6 is already mounted on /mnt/cfg/1

Setup sysmgr directories HW: 1, IFC:

Creating disk sysmgr directory

Checking Consistency Checker capability.

Card index is 21135

Supporting Consistency Checker.

Mounting ccheck tmpfs

Creating /var/sysmgr/tmp_logs/ccheck

Creating boot config file /mnt/cfg/0/boot/grub/menu.lst.local …

Creating boot config file /mnt/cfg/1/boot/grub/menu.lst.local …

Starting kdump:started up

*** Running INXOS PE IFC image ***

Cannot create link over existing -/var/lock-.

Cannot create link over existing -/var/log-.

Cannot create link over existing -/var/run-.

Cannot create link over existing -/var/tmp-.

Cannot create link over existing -/etc/resolv.conf-.

Undefined users:

> bind

Skipping /etc/default/volatiles/98_bind

Undefined users:

> bind

Skipping /etc/default/volatiles/99_bind_chroot

ALSA: Restoring mixer settings…

hostname: getline

Starting rpcbind daemon…done.

*** Running INXOS PE IFC image ***

card index: 21135, is_hw: 1, supervisor: 0, tor: 0, CORTINA1: 0

Simulation is set to 0

MPA_ID not set or -1: 0

chassis_model ;

slot_id ;

card_index 21135;

card_type ;

base mac ;

Main image

1 bin bin_ro boot bootflash bootflash-remote cfg0 cfg1 debug debugfs dev etc extract_start home init isan isanboot lib lib64 log

logflash logflash-remote m[ 36.495175] nvram_platform_tor_init Found IOFPGA device ID for nvram

edia mnt modflash nfsroot nginx nxos proc rd recovery root sbin securedata slot0 sys tmp usb usr usr_ro var vdc_2 vdc_3 vdc_4

volatile Removing /bootflash/policy_mgr_abort_dns /mnt/ifc/log 1 bin bin_ro boot bootflash bootflash-remote cfg0 cfg1 debug debugfs

dev etc extract_start home init isan isanboot lib lib64 log logflash logflash-remote media mnt modflash nfsroot nginx nxos proc rd

recovery root sbin securedata slot0 sys tmp usb usr usr_ro var vdc_2 vdc_3 vdc_4 volatile

Installing KLMs

Installing sse

Installing SSE module … done

Creating the sse device node … done

Setting up pss state

installing kpps

Installing klm_if_index

Installing KLM istack trace

Installing KIC

! 1 bin bin_ro boot bootflash bootflash-remote cfg0 cfg1 data_store debug debugfs dev etc extract_start home init isan isanboot lib

lib64 log logflash logflash-remote media mnt modflash nfsroot nginx nxos proc rd recovery root sbin securedata slot0 sys tmp usb usr

usr_ro var vdc_2 vdc_3 vdc_4 volatile Load non simulation KLMS ! 1 bin bin_ro boot bootflash bootflash-remote cfg0 cfg1 data_store

debug debugfs dev etc extract_start home init isan isanboot lib lib64[ 37.783484] imghdr (1549) Ran 5417 msecs in last 5424 msecs

log logflash logflash-remote media mnt modflash nfsroot nginx nxos proc rd recovery root sbin securedata slot0 sys tmp usb usr

usr_ro var vdc_2 vdc_3 vdc_4 volatile

Before proceeding further scan for all fpgas

*** Running INXOS PE IFC image ***

Installing nvram

Installing emmc

blogger: nothing to do.

Check/Create MMC parition

[ 45.972986] gzip (2027) Ran 4968 msecs in last 5004 msecs

[ 46.808355] imghdr (2029) Ran 5829 msecs in last 5836 msecs

Installing obfl emmc

Installing ins_gpl

Installing cctrl

Installing sprom[ 48.235047] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

Installing zc

Run the act2 sprom utility for tor

[ 51.784837] gzip (2027) Ran 5547 msecs in last 5748 msecs

[ 52.256882] imghdr (2029) Ran 5377 msecs in last 5384 msecs

SPROM setup successfully

Installing pfmcmn

Installing igb on TOR HW

Installing NF modules

net.ipv4.ip_nonlocal_bind = 1

net.core.wmem_max = 655355

net.core.rmem_max = 4194304

net.ipv4.conf.all.accept_redirects = 0

net.ipv4.conf.default.accept_redirects = 0

net.ipv4.conf.all.secure_redirects = 0

net.ipv4.conf.default.secure_redirects = 0

Chain PREROUTING (policy ACCEPT)

target prot opt source destination

Chain INPUT (policy ACCEPT)

target prot opt source destination

prefix all anywhere anywhere vrf 2

Chain FORWARD (policy ACCEPT)

target prot opt source destination

Chain OUTPUT (policy ACCEPT)

target prot opt source destination

Chain POSTROUTING (policy ACCEPT)

target prot opt source destination

IP: 10.177.12.242 MASK:255.255.0.0 GW:10.177.0.1 UP/DOWN:

eth0

Program the interface(eth0)/route

# This file is automatically generated don’t change it

auto lo

iface lo inet loopback

auto eth0

iface eth0 inet static

address 10.177.12.242

netmask 255.255.0.0

gateway 10.177.0.1

ifdown: interface eth0 not configured

Creating CGROUPS SS, BFD, IFC

cat: /sys.fs.cgroup/SS/memory.move_charge_at_immigrate: No such file or directory

Loading system software

/etc/rcS.d/S98microcode_ctl: microcode device /dev/cpu/microcode doesn’t exist?

*** Running INXOS PE IFC image ***

/etc/rcS.d/S98mount_obfl_supdc3: line 153: [: -o: integer expression expected

eMMC FLASH Device found…

e2fsck 1.42.1 (17-Feb-2012)

/dev/mmcblk0p2: recovering journal

[ 57.737413] imghdr (2029) Ran 5408 msecs in last 5416 msecs

[ 57.833422] gzip (2027) Ran 4633 msecs in last 5984 msecs

/dev/mmcblk0p2 has gone 198 days without being checked, check forced.

Pass 1: Checking inodes, blocks, and sizes

..done Wed Aug 5 12:36:21 UTC 2020

*** uncpmpress done ***

Pass 2: Checking directory structure

Pass 3: Checking directory connectivity

Pass 4: Checking reference counts

Pass 5: Checking group summary information

Free blocks count wrong (498821, counted=498817).

Fix? yes

/dev/mmcblk0p2: ***** FILE SYSTEM WAS MODIFIED *****

/dev/mmcblk0p2: 26/131072 files (30.8% non-contiguous), 25471/524288 blocks

nohup: redirecting stderr to stdout

*** Running INXOS PE IFC image ***

Starting system_stats daemon

Starting atd: OK

*** Running INXOS PE IFC image ***

System image extracted and uncompressed in background

In /etc/rcS.d/S99load-isan System image extracted 60.16

*** Loading system image from bootflash ***

In /etc/rcS.d/S99load-isan System image extraction done 60.17

Load plugins that defined in image conf: /isan/plugin_img/img.conf

Loading plugin 0: core_plugin…

[ 63.737992] imghdr (2029) Ran 5928 msecs in last 5936 msecs

[ 65.822195] gzip (2869) Ran 5579 msecs in last 5584 msecs

[ 69.738572] imghdr (2029) Ran 5928 msecs in last 5936 msecs

[ 71.111035] gzip (2869) Ran 5219 msecs in last 5224 msecs

[ 75.739153] imghdr (2029) Ran 5928 msecs in last 5936 msecs

[ 76.247201] gzip (2869) Ran 5064 msecs in last 5072 msecs

[ 81.739734] imghdr (2029) Ran 5928 msecs in last 5936 msecs

[ 81.803740] gzip (2869) Ran 5487 msecs in last 5488 msecs

[ 86.800226] gzip (2869) Ran 4985 msecs in last 5000 msecs

[ 87.740313] imghdr (2029) Ran 5863 msecs in last 5872 msecs

[ 92.276753] gzip (2869) Ran 5406 msecs in last 5412 msecs

*****************************************

Digital signature verification succesful for system image: “auto-s”

*****************************************

handle_platform_specific_conf_files: Pruning package specific files

card index from cmdline 21135

*** Running INXOS PE IFC image ***

card index from cmdline 21135

Pruning out MOCK specific files

Keep TOR/SDK. Remove SPINE,C1,ML specific conf files

Remove SIM specific conf files

Removing Dcimgr conf and cli file

Drop disk caches once plugins are loaded

[ 97.725287] imghdr (4504) Ran 5106 msecs in last 5116 msecs

chmod: cannot access `/usr/bin/ping6′: No such file or directory

card_index 21135;

[ 116.815129] gzip (5772) Ran 4953 msecs in last 5136 msecs

[ 122.815707] gzip (5772) Ran 5929 msecs in last 5936 msecs

[ 136.805059] gzip (6865) Ran 5123 msecs in last 5304 msecs

[ 142.805639] gzip (6865) Ran 5930 msecs in last 5936 msecs

/lc/isan/bin/inst_cmn: line 135: /lc/isan/bin/card_set_seq: No such file or directory

Now copying the hom emu.out

Port profile not found, catalog unchanged

[ 164.654991] gzip (9289) Ran 4617 msecs in last 5032 msecs

Now copying the hom emu.out

Port profile not found, catalog unchanged

[ 164.654991] gzip (9289) Ran 4617 msecs in last 5032 msecs

Unzipping pytz (in /usr/lib/python2.7/site-packages/pytz-2014.10-py2.7.egg)

INIT: Entering runlevel: 3

*** Running INXOS PE IFC image ***

======S99setup_lxc setup lxc for CentOS7 rootfs======

Starting system message bus: dbus.

*** Running INXOS PE IFC image ***

Restoring saved ssh keys

Starting OpenBSD Secure Shell server: sshd external

Fips mode enable 0

Starting OpenBSD Secure Shell server: sshd local

Fips mode enable 0

/etc/ssh/sshd_config_local line 98: Deprecated option UsePrivilegeSeparation

done.

Starting irqbalance: done

creating NFS state directory: done

Setting nlm_tcpport to $NLM_TCPPORTdone

starting 8 nfsd kernel threads: done

starting mountd: done

starting statd: done

Starting crond: OK

Stopping Bootlog daemon: bootlogd.

*** Running INXOS PE IFC image ***

Starting crond: OK

Stopping crond: OK

Skip updating lxc aci script

Starting libvirtd

crond stopped OK before restart

Starting crond: OK

Sending test message to kernel

Sending filter to KPM

Sending message to kernel to register the pid

Launching getty with console speed:9600

*** Running [ 184.710102] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

[ 184.863991] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

[ 184.958229] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

[ 185.076840] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

User Access Verification

(none) login: *** Running INXO[ 185.348727] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

S PE IFC image ***

[ 185.478509] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

*** Running INXO[ 185.589216] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

S PE IFC image ***

Installing FCOE [ 185.691964] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

module using inb[ 185.790346] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

and vegas … [ 185.863852] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

done

Installing FC2 module usin[ 185.973729] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

g inband kpm_inb[ 186.053506] sdwrap_event_hist_dbg_init_helper: Using GFP_ATOMIC for kmalloc!

vegas 9 … done

[ 186.179020] sdwrap_dbg_mod_init: Using GFP_ATOMIC for kmalloc!

[ 186.248959] sdwrap_event_hist_dbg_init_helper: Using GFP_ATOMIC for kmalloc!

*** Running INXOS PE IFC image ***

Aug 5 12:38:32 %CRDCFG-3-CRDCFG_ERR crdcfg_find_swcardid: own card previously not found. Searching.

Certificate verification passed

[ 212.701221] nvram_klm overwrote prev_rr[3]=140 prev_rr_str[3]=Power Cycle to nvram[ 212.828440] obfl_modify_last_rr:obfl_klm writing reset reason 140, Power Cycle

[ 212.924477] obfl_modify_last_rr : return value 88

Current SSD: TYPE=Micron_1100_MTFDDAV256TBN FW_VER=M0MUCW1

SSD firmware update is not required.

[ 323.936565] Hal (26973) Ran 5456 msecs in last 5852 msecs

[ 330.166545] Hal (26973) Ran 6137 msecs in last 6164 msecs

User Access Verification

(none) login:

Password: